Click on the IP Printer icon (top). Click on the '+' icon (lower left) to add a printer. Power off the print server, plug the usb from the printer into the server, then power on the server.Then do this:On Mac OS, open System Preferences and select ‘Print & Fax’.Q: How to reset the GlobeSurfer III and III+ to its default factory settings? A: Use a paper clip to push into the small hole next to the SIM tray when the device is powered on. This time, put your login in a safe place. After the reset, create again your username and password by going through the installation wizard. Please follow the procedure described in "How to reset the GlobeSurfer III and III+ to its default factory settings". Use with a RangeMax Dual Band Wireless-N Adapter and boost your performance and range.1 GlobeSurfer III+ FAQ version th Nov 2012 Device settings Q: I cannot remember my login to the device's admin pages, What to do? A: If you have forgotten your login, you will have to re-create it by resetting the device to its default factory setting.
![]() Change the setting in the 'Internet Protocol' section. Q: How do I change the default IP address of the GlobeSurfer III and III+ A: The default IP address of the router is If you need to change this IP address, you have to go to Advanced Mode -> Shortcuts -> Network Connections -> Lan Bridge -> Setting. Enter ' ' or 'globesurferiii' in the browser to access the admin pages. Netgear Wndr3300 Smart Setup Wizard Sierra Update Information CanThe device classifies the signal strength as Marginal, Poor, Good, Very Good, Excellent.Online Read How to Find Your Wired and Wireless MAC Addresses on Your Laptop. Antenna and signal reception Q: How do I know if my 3G reception is good or not? A: On the admin page home page, on the top left, you can see the name of the network operator, the connection technology as well as the signal strength. Q: Where can I find the latest firmware and how to do the update? A: Firmware update information can be found on our support website: For GlobeSurfer III: For GlobeSurfer III+ By default, the Liveupdate option is activated in your router and you will be automatically notified at the home page of the device admin GUI ( ) when there is a new firmware available. So choose your antenna with care. It is not rare that you will not have any improvement in using an average quality antenna. Q: What kind of gain could I expect by using an external antenna? A: The GlobeSurfer III and III+ already have very good reception. The type of connector is a mc-card connector. How can I improve my 3G reception? A: There is an external antenna connector on the device with which you can connect an external antenna. Only the owner/admin who has access to the admin pages is able to send and receive SMS. For detail installation procedure, please refer to our support website: For GlobeSurfer III: For GlobeSurfer III+ Q: Can I send and receive SMS? A: Yes, the GlobeSurfer III and III+ support both sending and receiving SMS. The GlobeSurfer III and III+ have a USB connection to which you can either add a USB memory or an external USB hard disk. Functional Q: Can I add memory to the GlobeSurfer III and III+ and make it available to all the network users? A: Yes. With this, you will never miss important SMS like roaming tariffs, volume limit alerts etc. Powering the device off and on will not clear the LED from flashing. For legal reasons, you have to actually read the SMS before the LED will stop flashing. If there is no missed call, then click on the 'SMS' tab and then 'Inbox' to check new SMS. To get the issue fixed, do the following : (1) Go to System -> Settings and in the HTTP interception section, make sure http interception is disabled (box not checked). Unfortunately the IP addresses used are very often , , , and which are precisely the same address used by the device itself for http interception. In order to reduce traffic, images are resized and stored on image servers. A: This is a known problem on some of the networks. Q: While loading Internet pages which contain many images, only some of the images are loaded, some are always missing. However in practical and in order to have optimum performance for every user, you should keep the number of users to around 20. These setting are to be verified with your service provider. What is wrong? A: Check if you have input the correct Access Point Name, Network Authentication, Login Username, Login Password. After this is done, all images should show up.5 Connection Q: I can see in the admin page the name of the operator and the signal strength is good, but the connection fails. If Username and/or Password is used, you have to set Network Authentication to either PAP or CHAP (if this has not been communicated by your service provider). In the UMTS section, input these settings. To input these settings, go to Advanced Mode -> Internet Connection -> Settings. In the UMTS section, put Network selection to 'Manual' and then click on the 'Scan for network' to search for all the networks in your neighbourhood. Go to Advanced Mode -> Internet Connection -> Settings. How can I avoid that? A: You will have to set the network selection to manual instead of leaving it in automatic. Q: I live at the border of my country and sometimes my GlobeSurfer is connected to my neighbouring country's network via roaming. If the GlobeSurfer does not need to supply any current to the USB nor to the telephone, then its consumption drops to 1.5 amperes. The car charger must be capable of delivering 3 amperes of current. You would need a car charger to convert the 12V from the car battery voltage to 5V used by the GlobeSurfer. Q: Can I use the GlobeSurfer III and III+ in my car? A: Yes. How do I know my data usage? A: In the admin home page, go to Advanced Mode -> System -> Settings. Nector.6 Q: I have limited data volume with my subscription. The connector type is a 2.1x5.5mm center positive standard connector. The most effective free mac system cleanerPlease check with your local service provider for further information. The only frequency band which the GlobeSurfer III+ does not have is the AWS band. Which are the countries where I can use the GlobeSurfer III+? A: The GlobeSurfer III+ can operate in 4 frequency bands in 3G (850/900/1900/2100 Mhz) which can cover all the European countries plus the majority of Asian, African, Middle East and American countries. The data usage counter will then be visible on the home page of the device GUI. Exe to dmg converter onlineAs a result, you cannot use a modem to transmit data over a digital mobile.7 Q: I have fixed my network type to 3G only (UMTS only in the GUI) and my phone does not work anymore. Unfortunately the Vocoder used in digital mobile phones (D-AMPS/GSM/CDMA) does not preserve phase relationships when compressing/uncompressing the analog data. A FAX modem, when operates above 600 bits per second, relies on phase shift keying. The FAX machine works differently than a normal voice device. Can I also connect a FAX machine to the phone connection? A: Unfortunately that would not be possible. Q: The GlobeSurfer III and III+ allow connection of a normal phone to receive mobile GSM calls. In the home page, please verify if you can see the name of the Operator and the Signal strength. What is wrong? A: Please login to the management console (by browsing to ). Q: When I try to connect to the mobile network either by the button on the device or by the GUI, the red telephone LED and the green globe LED start to flash very quickly and the connection fails. To solve the problem, set the connection method to UMTS preferred. If you set your network type to 3G only, the GlobeSurfer will not be listening any more to 2G phone calls. If you are not sure what to put in, please contact your service provider. In the UMTS section, input the correct Access point Name (APN), Network Authentication, Login Username, Login Password. To do that, go to Advanced Mode -> Internet Connection -> Settings. It means that you need to input the correct APN profile. ![]()
0 Comments
Leave a Reply. |
AuthorChristine ArchivesCategories |